Sony sound forge audio how to turn off track detection

#Sony sound forge audio how to turn off track detection full

Eliminate too wide of a frequency range, and you might adversely affect your desired sound or voice. But again, be careful the good sound, especially the human voice, exists over a wide spectrum of frequencies, so when you eliminate specific frequencies, youвЂ™re also eliminating parts of the voice or sound you want. Or, if you have a low-pitched rumble, possibly from wind noise, you may be able to eliminate those frequencies, too. Be careful, though, because any other sound (even desirable ones) may also contain that frequency and you'll alter those sounds with your EQ adjustment too. If you have a high-pitched tone or hiss prevalent in your audio, you may be able to use the equalizer to eliminate only the frequency of that tone, which would remove that sound. Lower some of the highs to bring down a bright-sounding room and possibly mitigate some echo, or you might lower some of the lower end to mitigate some bass distortion.Д«ecause equalizers let you enhance, soften, or eliminate specific frequencies, you can use them to eliminate specific problems in the sound while you leave the rest of the sound alone.

#Sony sound forge audio how to turn off track detection full

Bring up the bass for a more full sound, or вЂњfatten the middleвЂќ while tightening the top and bottom. Used well, the noise gate can be a great tool for helping to achieve a noise-free audio mix, but you can see that it requires a bit of careful adjustment and experimentation, as well as critical listening ears.Д®ditors often use equalizers to punch up sounds. In a case like that, you need a sophisticated noise reduction plug-in. That often makes for a worse final result than just leaving the noise in. But if you can hear the air conditioner noise clearly while she speaks and you remove it when she's not speaking, that noise is going to jump in and out of the recording. For instance, if you record an interview in a big room with a loud air conditioner running, you could set the gate to remove that air conditioner noise when your subject isn't talking. Keep one more consideration in mind: if your noise floor is too loud, the gate may not give you good results. A quicker release time lets the volume go back to normal more quickly, so the very first parts of words remain intact. If the release time is too long, the beginning of a sentence or word might get cut off by your lingering noise gate.

It dictates how long the gate stays engaged after the audio rises back above the threshold setting. The release slider does the same thing, only in reverse. At the ends of words or sentences, the drop-off will be more gradual, and the very ends of words wonвЂ™t cut out. If you set the attack time longer, the effect wonвЂ™t drop the volume as quickly, and little volume drops in the middle of words wonвЂ™t get caught in the gate, and thus be eliminated.

Think of it as turning a volume knob down quickly or slowly. The attack slider controls how quickly the effect lowers the volume when sound goes below the threshold. To help counter this, you need to adjust the gate's attack and release settings. This can happen not only between words, sentences, or paragraphs, but even within words themselves. This can make your audio sound choppy and cut off parts of words or other material you need. If reaction time isn't right, the gate might cut off the beginning and end of your desired audio. Second, as your desired sound begins and ends, the noise gate has to react. Sound complicated or difficult? Well, it can be, but with experience you'll get better at it. You must set the threshold in the perfect вЂњsweet spotвЂќ where it cuts out enough of the sound you don't want without cutting out too much of the sound you do want. When you use the noise gate, you can't avoid cutting out a portion of the sound you want. A good, robust recording-especially of the human voice - contains audio material at virtually every volume level between absolute silence (that's вЂњminus infinity,вЂќ or вЂњ-InfвЂќ in digital audio terms) up to your loudest volume peak. First, the noise gate can affect your desired sound material.

Sounds simple, right? Maybe, but keep a few important considerations in mind. The effect automatically drops the volume to zero whenever the sound's natural volume drops below the threshold, and the noise disappears. For example, to remove noise at -50 dB, set the noise gate threshold to -45 dB or so. The noise gate cuts off everything below a certain volume, known as the threshold volume.